Civil Engineering · Strength of Materials

Unit 3: Axial Loading MCQs

50 solved multiple choice questions with answers and short explanations.

Q1. Which statement best describes Axial member?

  1. Aa member loaded primarily along its longitudinal centroidal axis
  2. Bhas behavior influenced by both material yielding and instability
  3. Caxial force divided by the cross-sectional area, σ = P/A
  4. Dthe internal transverse force required for equilibrium of a cut segment
Show answer
Answer: A. a member loaded primarily along its longitudinal centroidal axisAxial member: a member loaded primarily along its longitudinal centroidal axis.
Report a mistake

Q2. Which concept is best described by the following statement: “a member loaded primarily along its longitudinal centroidal axis”?

  1. AYield strength
  2. BAxial member
  3. CLinear elastic behavior
  4. DStepped shaft total twist
Show answer
Answer: B. Axial memberAxial member: a member loaded primarily along its longitudinal centroidal axis.
Report a mistake

Q3. In Strength of Materials, which statement about Axial member is correct?

  1. Athe internal moment required for equilibrium of a cut segment
  2. Bθ = TL/(GJ) in linear elastic torsion
  3. Ca member loaded primarily along its longitudinal centroidal axis
  4. Dcauses a jump in the shear-force diagram equal to the load magnitude
Show answer
Answer: C. a member loaded primarily along its longitudinal centroidal axisAxial member: a member loaded primarily along its longitudinal centroidal axis.
Report a mistake

Q4. Select the correct relationship or description for Axial member.

  1. Athe internal transverse force required for equilibrium of a cut segment
  2. Btangential deviation is related to the first moment of the M/EI area
  3. Care oriented 45 degrees from the principal planes in stress transformation
  4. Da member loaded primarily along its longitudinal centroidal axis
Show answer
Answer: D. a member loaded primarily along its longitudinal centroidal axisAxial member: a member loaded primarily along its longitudinal centroidal axis.
Report a mistake

Q5. Which option correctly identifies Axial member?

  1. Aa member loaded primarily along its longitudinal centroidal axis
  2. Ba stress state in which stresses normal to one coordinate direction are negligible
  3. Cgeometric deformation conditions used with force-deformation relations
  4. Dτ = VQ/(It) under standard beam assumptions
Show answer
Answer: A. a member loaded primarily along its longitudinal centroidal axisAxial member: a member loaded primarily along its longitudinal centroidal axis.
Report a mistake

Q6. Which statement best describes Internal axial force?

  1. Adeformation that remains after the load is removed
  2. Bthe resultant normal force obtained from equilibrium of a cut section
  3. CEI times curvature is related to bending moment
  4. Dthe internal moment required for equilibrium of a cut segment
Show answer
Answer: B. the resultant normal force obtained from equilibrium of a cut sectionInternal axial force: the resultant normal force obtained from equilibrium of a cut section.
Report a mistake

Q7. Which concept is best described by the following statement: “the resultant normal force obtained from equilibrium of a cut section”?

  1. ADistributed load
  2. BTransformed-section method
  3. CInternal axial force
  4. DEuler buckling load dependence
Show answer
Answer: C. Internal axial forceInternal axial force: the resultant normal force obtained from equilibrium of a cut section.
Report a mistake

Q8. In Strength of Materials, which statement about Internal axial force is correct?

  1. Ashear force divided by resisting area, τ = V/A
  2. Bis parabolic over the depth and maximum at the neutral axis
  3. Cσ = My/I for elastic bending of a prismatic beam under standard assumptions
  4. Dthe resultant normal force obtained from equilibrium of a cut section
Show answer
Answer: D. the resultant normal force obtained from equilibrium of a cut sectionInternal axial force: the resultant normal force obtained from equilibrium of a cut section.
Report a mistake

Q9. Select the correct relationship or description for Internal axial force.

  1. Athe resultant normal force obtained from equilibrium of a cut section
  2. Bcan produce both direct normal stress and bending stress
  3. Care orientations at which the in-plane shear stress vanishes
  4. Da bar in axial tension usually contracts laterally
Show answer
Answer: A. the resultant normal force obtained from equilibrium of a cut sectionInternal axial force: the resultant normal force obtained from equilibrium of a cut section.
Report a mistake

Q10. Which option correctly identifies Internal axial force?

  1. Ahas compatible longitudinal strain at the interface between materials
  2. Bthe resultant normal force obtained from equilibrium of a cut section
  3. Cshear stress acting tangentially to the resisting cross section
  4. Dequals the radius of Mohr's circle for plane stress
Show answer
Answer: B. the resultant normal force obtained from equilibrium of a cut sectionInternal axial force: the resultant normal force obtained from equilibrium of a cut section.
Report a mistake

Q11. Which statement best describes Axial deformation of a uniform bar?

  1. Athe slope of the linear elastic stress-strain curve, E = σ/ε
  2. Bis the same through segments between applied torques when no intermediate torque is applied
  3. Cδ = PL/(AE) for constant axial load and linear elasticity
  4. Dcauses a jump in the shear-force diagram equal to the load magnitude
Show answer
Answer: C. δ = PL/(AE) for constant axial load and linear elasticityAxial deformation of a uniform bar: δ = PL/(AE) for constant axial load and linear elasticity.
Report a mistake

Q12. Which concept is best described by the following statement: “δ = PL/(AE) for constant axial load and linear elasticity”?

  1. AFirst moment-area theorem
  2. BTorsional rigidity
  3. CRequirement for superposition
  4. DAxial deformation of a uniform bar
Show answer
Answer: D. Axial deformation of a uniform barAxial deformation of a uniform bar: δ = PL/(AE) for constant axial load and linear elasticity.
Report a mistake

Q13. In Strength of Materials, which statement about Axial deformation of a uniform bar is correct?

  1. Aδ = PL/(AE) for constant axial load and linear elasticity
  2. Bthe ability of a material to recover its original dimensions after unloading
  3. Cchange in slope equals the area under the M/EI diagram between two points
  4. Dis linear with distance from the neutral axis in simple elastic bending
Show answer
Answer: A. δ = PL/(AE) for constant axial load and linear elasticityAxial deformation of a uniform bar: δ = PL/(AE) for constant axial load and linear elasticity.
Report a mistake

Q14. Select the correct relationship or description for Axial deformation of a uniform bar.

  1. Athe ability of a material to recover its original dimensions after unloading
  2. Bδ = PL/(AE) for constant axial load and linear elasticity
  3. Cθ = TL/(GJ) in linear elastic torsion
  4. Da stability failure involving lateral deflection of a compressed member
Show answer
Answer: B. δ = PL/(AE) for constant axial load and linear elasticityAxial deformation of a uniform bar: δ = PL/(AE) for constant axial load and linear elasticity.
Report a mistake

Q15. Which option correctly identifies Axial deformation of a uniform bar?

  1. Aoccurs at the outer surface of a solid circular shaft in elastic torsion
  2. Badds responses from individual loads when behavior is linear elastic
  3. Cδ = PL/(AE) for constant axial load and linear elasticity
  4. Ddevelops shear stress over its cross section
Show answer
Answer: C. δ = PL/(AE) for constant axial load and linear elasticityAxial deformation of a uniform bar: δ = PL/(AE) for constant axial load and linear elasticity.
Report a mistake

Q16. Which statement best describes Axial rigidity?

  1. Aapproximately equal to the change in angle measured in radians
  2. Bthe internal transverse force required for equilibrium of a cut segment
  3. Cσ = EαΔT in magnitude for a temperature change under ideal full restraint
  4. Dthe product AE, which resists axial deformation
Show answer
Answer: D. the product AE, which resists axial deformationAxial rigidity: the product AE, which resists axial deformation.
Report a mistake

Q17. Which concept is best described by the following statement: “the product AE, which resists axial deformation”?

  1. AAxial rigidity
  2. BTensile normal stress
  3. CEuler critical load
  4. DSeries shaft torque
Show answer
Answer: A. Axial rigidityAxial rigidity: the product AE, which resists axial deformation.
Report a mistake

Q18. In Strength of Materials, which statement about Axial rigidity is correct?

  1. Achange in slope equals the area under the M/EI diagram between two points
  2. Bthe product AE, which resists axial deformation
  3. Cis most appropriate for long, slender columns that buckle elastically
  4. Dcauses a jump in the shear-force diagram equal to the load magnitude
Show answer
Answer: B. the product AE, which resists axial deformationAxial rigidity: the product AE, which resists axial deformation.
Report a mistake

Q19. Select the correct relationship or description for Axial rigidity.

  1. Aτ = VQ/(It) under standard beam assumptions
  2. Bthe resultant normal force obtained from equilibrium of a cut section
  3. Cthe product AE, which resists axial deformation
  4. Dhas compatible longitudinal strain at the interface between materials
Show answer
Answer: C. the product AE, which resists axial deformationAxial rigidity: the product AE, which resists axial deformation.
Report a mistake

Q20. Which option correctly identifies Axial rigidity?

  1. Adevelops shear stress over its cross section
  2. Ba stability failure involving lateral deflection of a compressed member
  3. Cr = sqrt(I/A)
  4. Dthe product AE, which resists axial deformation
Show answer
Answer: D. the product AE, which resists axial deformationAxial rigidity: the product AE, which resists axial deformation.
Report a mistake

Q21. Which statement best describes Axially indeterminate system?

  1. Aa system requiring compatibility equations in addition to equilibrium
  2. Bis zero
  3. Coccurs at the outer surface of a solid circular shaft in elastic torsion
  4. Da member made of two or more materials constrained to deform compatibly
Show answer
Answer: A. a system requiring compatibility equations in addition to equilibriumAxially indeterminate system: a system requiring compatibility equations in addition to equilibrium.
Report a mistake

Q22. Which concept is best described by the following statement: “a system requiring compatibility equations in addition to equilibrium”?

  1. ARadius of Mohr's circle
  2. BAxially indeterminate system
  3. CCritical buckling load
  4. DShear flow
Show answer
Answer: B. Axially indeterminate systemAxially indeterminate system: a system requiring compatibility equations in addition to equilibrium.
Report a mistake

Q23. In Strength of Materials, which statement about Axially indeterminate system is correct?

  1. Ais most appropriate for long, slender columns that buckle elastically
  2. Bthe product GJ
  3. Ca system requiring compatibility equations in addition to equilibrium
  4. Ddimensionless because it is a ratio of two lengths
Show answer
Answer: C. a system requiring compatibility equations in addition to equilibriumAxially indeterminate system: a system requiring compatibility equations in addition to equilibrium.
Report a mistake

Q24. Select the correct relationship or description for Axially indeterminate system.

  1. Aare orientations at which the in-plane shear stress vanishes
  2. Ba stability failure involving lateral deflection of a compressed member
  3. Cω = 2πN/60 when N is in revolutions per minute
  4. Da system requiring compatibility equations in addition to equilibrium
Show answer
Answer: D. a system requiring compatibility equations in addition to equilibriumAxially indeterminate system: a system requiring compatibility equations in addition to equilibrium.
Report a mistake

Q25. Which option correctly identifies Axially indeterminate system?

  1. Aa system requiring compatibility equations in addition to equilibrium
  2. Bgeometric deformation conditions used with force-deformation relations
  3. Cthe ability of a material to undergo permanent deformation without rupture
  4. Da load spread continuously along a length and expressed as force per unit length
Show answer
Answer: A. a system requiring compatibility equations in addition to equilibriumAxially indeterminate system: a system requiring compatibility equations in addition to equilibrium.
Report a mistake

Q26. Which statement best describes Compatibility in axial members?

  1. Aσ = Eε for a linear elastic material
  2. Bgeometric deformation conditions used with force-deformation relations
  3. Ccan produce both direct normal stress and bending stress
  4. DP = Tω
Show answer
Answer: B. geometric deformation conditions used with force-deformation relationsCompatibility in axial members: geometric deformation conditions used with force-deformation relations.
Report a mistake

Q27. Which concept is best described by the following statement: “geometric deformation conditions used with force-deformation relations”?

  1. AFree thermal strain
  2. BNormal stress
  3. CCompatibility in axial members
  4. DConnectors in built-up beams
Show answer
Answer: C. Compatibility in axial membersCompatibility in axial members: geometric deformation conditions used with force-deformation relations.
Report a mistake

Q28. In Strength of Materials, which statement about Compatibility in axial members is correct?

  1. AKL/r, where r is the radius of gyration
  2. BP = Tω
  3. Cnormal stresses acting on planes where shear stress is zero
  4. Dgeometric deformation conditions used with force-deformation relations
Show answer
Answer: D. geometric deformation conditions used with force-deformation relationsCompatibility in axial members: geometric deformation conditions used with force-deformation relations.
Report a mistake

Q29. Select the correct relationship or description for Compatibility in axial members.

  1. Ageometric deformation conditions used with force-deformation relations
  2. Bthe greatest stress that can be removed without permanent deformation
  3. Ccommonly has a pin support and a roller support
  4. Dthe negative ratio of lateral strain to longitudinal strain
Show answer
Answer: A. geometric deformation conditions used with force-deformation relationsCompatibility in axial members: geometric deformation conditions used with force-deformation relations.
Report a mistake

Q30. Which option correctly identifies Compatibility in axial members?

  1. Adeformation that remains after the load is removed
  2. Bgeometric deformation conditions used with force-deformation relations
  3. Cτ = VQ/(It) under standard beam assumptions
  4. Dis the first moment of the relevant partial area about the neutral axis
Show answer
Answer: B. geometric deformation conditions used with force-deformation relationsCompatibility in axial members: geometric deformation conditions used with force-deformation relations.
Report a mistake

Q31. Which statement best describes Free thermal strain?

  1. Ais generally nonuniform over the depth of a typical beam cross section
  2. Bthe negative ratio of lateral strain to longitudinal strain
  3. Cε_th = αΔT when thermal expansion is unrestrained
  4. Ddimensionless because it is a ratio of two lengths
Show answer
Answer: C. ε_th = αΔT when thermal expansion is unrestrainedFree thermal strain: ε_th = αΔT when thermal expansion is unrestrained.
Report a mistake

Q32. Which concept is best described by the following statement: “ε_th = αΔT when thermal expansion is unrestrained”?

  1. AShear stress at the top and bottom free surfaces of a rectangular beam
  2. BSuperposition for beam deflection
  3. CLoad-shear differential relation
  4. DFree thermal strain
Show answer
Answer: D. Free thermal strainFree thermal strain: ε_th = αΔT when thermal expansion is unrestrained.
Report a mistake

Q33. In Strength of Materials, which statement about Free thermal strain is correct?

  1. Aε_th = αΔT when thermal expansion is unrestrained
  2. Ba member loaded primarily along its longitudinal centroidal axis
  3. Chas effective-length factor K = 1
  4. Dis linear with distance from the neutral axis in simple elastic bending
Show answer
Answer: A. ε_th = αΔT when thermal expansion is unrestrainedFree thermal strain: ε_th = αΔT when thermal expansion is unrestrained.
Report a mistake

Q34. Select the correct relationship or description for Free thermal strain.

  1. Arequires superposition of stress components when linear elastic assumptions apply
  2. Bε_th = αΔT when thermal expansion is unrestrained
  3. Carises from internal shear force acting across the cross section
  4. DdV/dx = -w under the common sign convention
Show answer
Answer: B. ε_th = αΔT when thermal expansion is unrestrainedFree thermal strain: ε_th = αΔT when thermal expansion is unrestrained.
Report a mistake

Q35. Which option correctly identifies Free thermal strain?

  1. Aangular distortion produced by shear stress
  2. Bhas behavior influenced by both material yielding and instability
  3. Cε_th = αΔT when thermal expansion is unrestrained
  4. Dnormal stresses acting on planes where shear stress is zero
Show answer
Answer: C. ε_th = αΔT when thermal expansion is unrestrainedFree thermal strain: ε_th = αΔT when thermal expansion is unrestrained.
Report a mistake

Q36. Which statement best describes Thermal stress in a fully restrained uniform bar?

  1. Acan produce both direct normal stress and bending stress
  2. Bchange in slope equals the area under the M/EI diagram between two points
  3. Cdeformation that remains after the load is removed
  4. Dσ = EαΔT in magnitude for a temperature change under ideal full restraint
Show answer
Answer: D. σ = EαΔT in magnitude for a temperature change under ideal full restraintThermal stress in a fully restrained uniform bar: σ = EαΔT in magnitude for a temperature change under ideal full restraint.
Report a mistake

Q37. Which concept is best described by the following statement: “σ = EαΔT in magnitude for a temperature change under ideal full restraint”?

  1. AThermal stress in a fully restrained uniform bar
  2. BAngular speed relation
  3. CAxial member
  4. DConcentrated couple effect on moment diagram
Show answer
Answer: A. Thermal stress in a fully restrained uniform barThermal stress in a fully restrained uniform bar: σ = EαΔT in magnitude for a temperature change under ideal full restraint.
Report a mistake

Q38. In Strength of Materials, which statement about Thermal stress in a fully restrained uniform bar is correct?

  1. Athe maximum engineering stress reached on a tensile stress-strain curve
  2. Bσ = EαΔT in magnitude for a temperature change under ideal full restraint
  3. Cdimensionless because it is a ratio of two lengths
  4. Dchanges across the neutral axis, with one side in tension and the other in compression
Show answer
Answer: B. σ = EαΔT in magnitude for a temperature change under ideal full restraintThermal stress in a fully restrained uniform bar: σ = EαΔT in magnitude for a temperature change under ideal full restraint.
Report a mistake

Q39. Select the correct relationship or description for Thermal stress in a fully restrained uniform bar.

  1. AdM/dx = V under the common sign convention
  2. Bapproximately equal to the change in angle measured in radians
  3. Cσ = EαΔT in magnitude for a temperature change under ideal full restraint
  4. Ddepends on material stiffness and cross-sectional area
Show answer
Answer: C. σ = EαΔT in magnitude for a temperature change under ideal full restraintThermal stress in a fully restrained uniform bar: σ = EαΔT in magnitude for a temperature change under ideal full restraint.
Report a mistake

Q40. Which option correctly identifies Thermal stress in a fully restrained uniform bar?

  1. Achange in slope equals the area under the M/EI diagram between two points
  2. Bare determined from beam boundary and continuity conditions
  3. Cshear force divided by resisting area, τ = V/A
  4. Dσ = EαΔT in magnitude for a temperature change under ideal full restraint
Show answer
Answer: D. σ = EαΔT in magnitude for a temperature change under ideal full restraintThermal stress in a fully restrained uniform bar: σ = EαΔT in magnitude for a temperature change under ideal full restraint.
Report a mistake

Q41. Which statement best describes Composite axial member?

  1. Aa member made of two or more materials constrained to deform compatibly
  2. Bis proportional to flexural rigidity EI and inversely proportional to effective length squared
  3. Cchanges across the neutral axis, with one side in tension and the other in compression
  4. Dσ = Eε for a linear elastic material
Show answer
Answer: A. a member made of two or more materials constrained to deform compatiblyComposite axial member: a member made of two or more materials constrained to deform compatibly.
Report a mistake

Q42. Which concept is best described by the following statement: “a member made of two or more materials constrained to deform compatibly”?

  1. APoint load effect on shear diagram
  2. BComposite axial member
  3. CEccentric axial load
  4. DMaximum elastic bending stress
Show answer
Answer: B. Composite axial memberComposite axial member: a member made of two or more materials constrained to deform compatibly.
Report a mistake

Q43. In Strength of Materials, which statement about Composite axial member is correct?

  1. Aτ = VQ/(It) under standard beam assumptions
  2. BdM/dx = V under the common sign convention
  3. Ca member made of two or more materials constrained to deform compatibly
  4. Dhas behavior influenced by both material yielding and instability
Show answer
Answer: C. a member made of two or more materials constrained to deform compatiblyComposite axial member: a member made of two or more materials constrained to deform compatibly.
Report a mistake

Q44. Select the correct relationship or description for Composite axial member.

  1. Aare oriented 45 degrees from the principal planes in stress transformation
  2. Bis linear with distance from the neutral axis in simple elastic bending
  3. Cdimensionless because it is a ratio of two lengths
  4. Da member made of two or more materials constrained to deform compatibly
Show answer
Answer: D. a member made of two or more materials constrained to deform compatiblyComposite axial member: a member made of two or more materials constrained to deform compatibly.
Report a mistake

Q45. Which option correctly identifies Composite axial member?

  1. Aa member made of two or more materials constrained to deform compatibly
  2. Baxial force divided by the cross-sectional area, σ = P/A
  3. Cpasses through the centroid for a homogeneous prismatic beam under pure bending
  4. Dchange in length divided by original length, ε = ΔL/L
Show answer
Answer: A. a member made of two or more materials constrained to deform compatiblyComposite axial member: a member made of two or more materials constrained to deform compatibly.
Report a mistake

Q46. Which statement best describes Load sharing in a bonded composite bar?

  1. Aequals load intensity times loaded length and acts at the midpoint of that length
  2. Bdepends on material stiffness and cross-sectional area
  3. CS = I/c, where c is the distance to the extreme fiber
  4. Ddeformation that remains after the load is removed
Show answer
Answer: B. depends on material stiffness and cross-sectional areaLoad sharing in a bonded composite bar: depends on material stiffness and cross-sectional area.
Report a mistake

Q47. Which concept is best described by the following statement: “depends on material stiffness and cross-sectional area”?

  1. AElastic torsion formula
  2. BPrincipal stresses
  3. CLoad sharing in a bonded composite bar
  4. DAngular speed relation
Show answer
Answer: C. Load sharing in a bonded composite barLoad sharing in a bonded composite bar: depends on material stiffness and cross-sectional area.
Report a mistake

Q48. In Strength of Materials, which statement about Load sharing in a bonded composite bar is correct?

  1. Ais the same through segments between applied torques when no intermediate torque is applied
  2. Bequals load intensity times loaded length and acts at the midpoint of that length
  3. Cthe deflected shape of a beam's neutral axis
  4. Ddepends on material stiffness and cross-sectional area
Show answer
Answer: D. depends on material stiffness and cross-sectional areaLoad sharing in a bonded composite bar: depends on material stiffness and cross-sectional area.
Report a mistake

Q49. Select the correct relationship or description for Load sharing in a bonded composite bar.

  1. Adepends on material stiffness and cross-sectional area
  2. Bhas effective-length factor K = 1
  3. Cthe algebraic sum of the twists of its individual segments
  4. Doccurs at the extreme fiber farthest from the neutral axis
Show answer
Answer: A. depends on material stiffness and cross-sectional areaLoad sharing in a bonded composite bar: depends on material stiffness and cross-sectional area.
Report a mistake

Q50. Which option correctly identifies Load sharing in a bonded composite bar?

  1. Aare designed to transfer interface shear so the components act together
  2. Bdepends on material stiffness and cross-sectional area
  3. Cthe resultant normal force obtained from equilibrium of a cut section
  4. Dr = sqrt(I/A)
Show answer
Answer: B. depends on material stiffness and cross-sectional areaLoad sharing in a bonded composite bar: depends on material stiffness and cross-sectional area.
Report a mistake