Civil Engineering · Structural Analysis

Unit 3: Trusses MCQs

50 solved multiple choice questions with answers and short explanations.

Q1. Which statement best describes ideal truss member?

  1. Ais treated as a two-force member carrying axial tension or compression
  2. Bcarries bending only
  3. Ccarries torsion only
  4. Dhas distributed loading along its length
Show answer
Answer: A. is treated as a two-force member carrying axial tension or compressionIn structural analysis, ideal truss member is correctly described as follows: is treated as a two-force member carrying axial tension or compression.
Report a mistake

Q2. Which concept is associated with the statement: “is treated as a two-force member carrying axial tension or compression”?

  1. Aa quantity unrelated to this topic
  2. Ba material-strength parameter only
  3. Ca drafting convention only
  4. Dideal truss member
Show answer
Answer: D. ideal truss memberThe statement describes ideal truss member.
Report a mistake

Q3. Which statement best describes ideal truss joint?

  1. Ais always fully rigid
  2. Btransfers a prescribed moment
  3. Cprevents member rotation
  4. Dis modeled as a frictionless pin
Show answer
Answer: D. is modeled as a frictionless pinIn structural analysis, ideal truss joint is correctly described as follows: is modeled as a frictionless pin.
Report a mistake

Q4. Which concept is associated with the statement: “is modeled as a frictionless pin”?

  1. Aa material-strength parameter only
  2. Ba drafting convention only
  3. Cideal truss joint
  4. Da quantity unrelated to this topic
Show answer
Answer: C. ideal truss jointThe statement describes ideal truss joint.
Report a mistake

Q5. Which statement best describes truss loading assumption?

  1. Aloads cannot act vertically
  2. Bself-weight must always be ignored
  3. Cexternal loads are applied at joints in the ideal model
  4. Dloads act only at member midpoints
Show answer
Answer: C. external loads are applied at joints in the ideal modelIn structural analysis, truss loading assumption is correctly described as follows: external loads are applied at joints in the ideal model.
Report a mistake

Q6. Which concept is associated with the statement: “external loads are applied at joints in the ideal model”?

  1. Aa drafting convention only
  2. Btruss loading assumption
  3. Ca quantity unrelated to this topic
  4. Da material-strength parameter only
Show answer
Answer: B. truss loading assumptionThe statement describes truss loading assumption.
Report a mistake

Q7. Which statement best describes tension member?

  1. Amust be vertical
  2. Bpulls away from a joint in the usual joint-force convention
  3. Calways pushes toward a joint
  4. Dhas zero axial force
Show answer
Answer: B. pulls away from a joint in the usual joint-force conventionIn structural analysis, tension member is correctly described as follows: pulls away from a joint in the usual joint-force convention.
Report a mistake

Q8. Which concept is associated with the statement: “pulls away from a joint in the usual joint-force convention”?

  1. Atension member
  2. Ba quantity unrelated to this topic
  3. Ca material-strength parameter only
  4. Da drafting convention only
Show answer
Answer: A. tension memberThe statement describes tension member.
Report a mistake

Q9. Which statement best describes compression member?

  1. Apushes toward a joint in the usual joint-force convention
  2. Balways pulls away from a joint
  3. Ccannot buckle
  4. Dhas no axial force
Show answer
Answer: A. pushes toward a joint in the usual joint-force conventionIn structural analysis, compression member is correctly described as follows: pushes toward a joint in the usual joint-force convention.
Report a mistake

Q10. Which concept is associated with the statement: “pushes toward a joint in the usual joint-force convention”?

  1. Aa material-strength parameter only
  2. Ba drafting convention only
  3. Ccompression member
  4. Da quantity unrelated to this topic
Show answer
Answer: C. compression memberThe statement describes compression member.
Report a mistake

Q11. Which statement best describes method of joints?

  1. Aapplies equilibrium to individual truss joints
  2. Bcuts through several members at once
  3. Cuses only compatibility equations
  4. Dis limited to beams
Show answer
Answer: A. applies equilibrium to individual truss jointsIn structural analysis, method of joints is correctly described as follows: applies equilibrium to individual truss joints.
Report a mistake

Q12. Which concept is associated with the statement: “applies equilibrium to individual truss joints”?

  1. Aa quantity unrelated to this topic
  2. Ba material-strength parameter only
  3. Ca drafting convention only
  4. Dmethod of joints
Show answer
Answer: D. method of jointsThe statement describes method of joints.
Report a mistake

Q13. Which statement best describes starting joint?

  1. Amust have at least four unknowns
  2. Bmust be an internal hinge only
  3. Ccannot be at a support
  4. Dpreferably has no more than two unknown member forces
Show answer
Answer: D. preferably has no more than two unknown member forcesIn structural analysis, starting joint is correctly described as follows: preferably has no more than two unknown member forces.
Report a mistake

Q14. Which concept is associated with the statement: “preferably has no more than two unknown member forces”?

  1. Aa material-strength parameter only
  2. Ba drafting convention only
  3. Cstarting joint
  4. Da quantity unrelated to this topic
Show answer
Answer: C. starting jointThe statement describes starting joint.
Report a mistake

Q15. Which statement best describes joint equilibrium in a planar truss?

  1. Auses three moment equations
  2. Brequires deflection compatibility
  3. Cuses ΣFx = 0 and ΣFy = 0
  4. Duses only ΣM = 0
Show answer
Answer: C. uses ΣFx = 0 and ΣFy = 0In structural analysis, joint equilibrium in a planar truss is correctly described as follows: uses ΣFx = 0 and ΣFy = 0.
Report a mistake

Q16. Which concept is associated with the statement: “uses ΣFx = 0 and ΣFy = 0”?

  1. Aa drafting convention only
  2. Bjoint equilibrium in a planar truss
  3. Ca quantity unrelated to this topic
  4. Da material-strength parameter only
Show answer
Answer: B. joint equilibrium in a planar trussThe statement describes joint equilibrium in a planar truss.
Report a mistake

Q17. Which statement best describes assumed member force direction?

  1. Ahas no sign meaning
  2. Bmay initially be taken as tension, with a negative result indicating compression
  3. Cmust always be known beforehand
  4. Dcannot be changed after calculation
Show answer
Answer: B. may initially be taken as tension, with a negative result indicating compressionIn structural analysis, assumed member force direction is correctly described as follows: may initially be taken as tension, with a negative result indicating compression.
Report a mistake

Q18. Which concept is associated with the statement: “may initially be taken as tension, with a negative result indicating compression”?

  1. Aassumed member force direction
  2. Ba quantity unrelated to this topic
  3. Ca material-strength parameter only
  4. Da drafting convention only
Show answer
Answer: A. assumed member force directionThe statement describes assumed member force direction.
Report a mistake

Q19. Which statement best describes joint-by-joint progression?

  1. Aknown member forces from one joint help solve adjacent joints
  2. Beach joint is completely unrelated
  3. Csupport reactions are never needed
  4. Dmoments at ideal joints are primary unknowns
Show answer
Answer: A. known member forces from one joint help solve adjacent jointsIn structural analysis, joint-by-joint progression is correctly described as follows: known member forces from one joint help solve adjacent joints.
Report a mistake

Q20. Which concept is associated with the statement: “known member forces from one joint help solve adjacent joints”?

  1. Aa material-strength parameter only
  2. Ba drafting convention only
  3. Cjoint-by-joint progression
  4. Da quantity unrelated to this topic
Show answer
Answer: C. joint-by-joint progressionThe statement describes joint-by-joint progression.
Report a mistake

Q21. Which statement best describes method of sections?

  1. Afinds selected truss member forces by cutting through the truss
  2. Brequires solving every joint first
  3. Cis used only for continuous beams
  4. Dcannot use moment equilibrium
Show answer
Answer: A. finds selected truss member forces by cutting through the trussIn structural analysis, method of sections is correctly described as follows: finds selected truss member forces by cutting through the truss.
Report a mistake

Q22. Which concept is associated with the statement: “finds selected truss member forces by cutting through the truss”?

  1. Aa quantity unrelated to this topic
  2. Ba material-strength parameter only
  3. Ca drafting convention only
  4. Dmethod of sections
Show answer
Answer: D. method of sectionsThe statement describes method of sections.
Report a mistake

Q23. Which statement best describes useful section cut?

  1. Amust pass through every member
  2. Bmust contain no unknown member
  3. Calways passes through supports only
  4. Dusually passes through no more than three unknown member forces in a planar truss
Show answer
Answer: D. usually passes through no more than three unknown member forces in a planar trussIn structural analysis, useful section cut is correctly described as follows: usually passes through no more than three unknown member forces in a planar truss.
Report a mistake

Q24. Which concept is associated with the statement: “usually passes through no more than three unknown member forces in a planar truss”?

  1. Aa material-strength parameter only
  2. Ba drafting convention only
  3. Cuseful section cut
  4. Da quantity unrelated to this topic
Show answer
Answer: C. useful section cutThe statement describes useful section cut.
Report a mistake

Q25. Which statement best describes moment equation in method of sections?

  1. Arequires all forces to be parallel
  2. Bis valid only at joints
  3. Ccan eliminate unknown forces whose lines of action pass through the moment center
  4. Dcannot be used for trusses
Show answer
Answer: C. can eliminate unknown forces whose lines of action pass through the moment centerIn structural analysis, moment equation in method of sections is correctly described as follows: can eliminate unknown forces whose lines of action pass through the moment center.
Report a mistake

Q26. Which concept is associated with the statement: “can eliminate unknown forces whose lines of action pass through the moment center”?

  1. Aa drafting convention only
  2. Bmoment equation in method of sections
  3. Ca quantity unrelated to this topic
  4. Da material-strength parameter only
Show answer
Answer: B. moment equation in method of sectionsThe statement describes moment equation in method of sections.
Report a mistake

Q27. Which statement best describes section equilibrium?

  1. Arequires member stiffness
  2. Buses planar equilibrium equations on either cut portion
  3. Cuses compatibility only
  4. Dignores support reactions
Show answer
Answer: B. uses planar equilibrium equations on either cut portionIn structural analysis, section equilibrium is correctly described as follows: uses planar equilibrium equations on either cut portion.
Report a mistake

Q28. Which concept is associated with the statement: “uses planar equilibrium equations on either cut portion”?

  1. Asection equilibrium
  2. Ba quantity unrelated to this topic
  3. Ca material-strength parameter only
  4. Da drafting convention only
Show answer
Answer: A. section equilibriumThe statement describes section equilibrium.
Report a mistake

Q29. Which statement best describes advantage of sections?

  1. Ait can obtain a few desired member forces without analyzing the entire truss
  2. Bit automatically gives all deflections
  3. Cit removes need for reactions
  4. Dit applies only to zero-force members
Show answer
Answer: A. it can obtain a few desired member forces without analyzing the entire trussIn structural analysis, advantage of sections is correctly described as follows: it can obtain a few desired member forces without analyzing the entire truss.
Report a mistake

Q30. Which concept is associated with the statement: “it can obtain a few desired member forces without analyzing the entire truss”?

  1. Aa material-strength parameter only
  2. Ba drafting convention only
  3. Cadvantage of sections
  4. Da quantity unrelated to this topic
Show answer
Answer: C. advantage of sectionsThe statement describes advantage of sections.
Report a mistake

Q31. Which statement best describes two non-collinear members at an unloaded joint?

  1. Aboth are zero-force members when no external load or support reaction acts at that joint
  2. Bboth must be in compression
  3. Cboth must be in tension
  4. Dneither can be zero
Show answer
Answer: A. both are zero-force members when no external load or support reaction acts at that jointIn structural analysis, two non-collinear members at an unloaded joint is correctly described as follows: both are zero-force members when no external load or support reaction acts at that joint.
Report a mistake

Q32. Which concept is associated with the statement: “both are zero-force members when no external load or support reaction acts at that joint”?

  1. Aa quantity unrelated to this topic
  2. Ba material-strength parameter only
  3. Ca drafting convention only
  4. Dtwo non-collinear members at an unloaded joint
Show answer
Answer: D. two non-collinear members at an unloaded jointThe statement describes two non-collinear members at an unloaded joint.
Report a mistake

Q33. Which statement best describes three-member unloaded joint with two collinear members?

  1. Aall three are necessarily zero
  2. Bthe two collinear members are zero
  3. Cthe non-collinear member carries maximum force
  4. Dthe non-collinear member is a zero-force member
Show answer
Answer: D. the non-collinear member is a zero-force memberIn structural analysis, three-member unloaded joint with two collinear members is correctly described as follows: the non-collinear member is a zero-force member.
Report a mistake

Q34. Which concept is associated with the statement: “the non-collinear member is a zero-force member”?

  1. Aa material-strength parameter only
  2. Ba drafting convention only
  3. Cthree-member unloaded joint with two collinear members
  4. Da quantity unrelated to this topic
Show answer
Answer: C. three-member unloaded joint with two collinear membersThe statement describes three-member unloaded joint with two collinear members.
Report a mistake

Q35. Which statement best describes purpose of identifying zero-force members?

  1. Ait determines deflection directly
  2. Bit changes support reactions
  3. Cit simplifies truss analysis and reveals members inactive for a particular loading case
  4. Dit proves the member can always be removed
Show answer
Answer: C. it simplifies truss analysis and reveals members inactive for a particular loading caseIn structural analysis, purpose of identifying zero-force members is correctly described as follows: it simplifies truss analysis and reveals members inactive for a particular loading case.
Report a mistake

Q36. Which concept is associated with the statement: “it simplifies truss analysis and reveals members inactive for a particular loading case”?

  1. Aa drafting convention only
  2. Bpurpose of identifying zero-force members
  3. Ca quantity unrelated to this topic
  4. Da material-strength parameter only
Show answer
Answer: B. purpose of identifying zero-force membersThe statement describes purpose of identifying zero-force members.
Report a mistake

Q37. Which statement best describes zero-force designation?

  1. Ais determined only by material
  2. Bdepends on the loading and support condition being analyzed
  3. Cmeans the member is structurally useless in every case
  4. Dmeans the member has zero length
Show answer
Answer: B. depends on the loading and support condition being analyzedIn structural analysis, zero-force designation is correctly described as follows: depends on the loading and support condition being analyzed.
Report a mistake

Q38. Which concept is associated with the statement: “depends on the loading and support condition being analyzed”?

  1. Azero-force designation
  2. Ba quantity unrelated to this topic
  3. Ca material-strength parameter only
  4. Da drafting convention only
Show answer
Answer: A. zero-force designationThe statement describes zero-force designation.
Report a mistake

Q39. Which statement best describes joint inspection?

  1. Acan identify some zero-force members before solving numerical equilibrium
  2. Bcan never reveal member force information
  3. Crequires stiffness matrices
  4. Dis applicable only after deflection analysis
Show answer
Answer: A. can identify some zero-force members before solving numerical equilibriumIn structural analysis, joint inspection is correctly described as follows: can identify some zero-force members before solving numerical equilibrium.
Report a mistake

Q40. Which concept is associated with the statement: “can identify some zero-force members before solving numerical equilibrium”?

  1. Aa material-strength parameter only
  2. Ba drafting convention only
  3. Cjoint inspection
  4. Da quantity unrelated to this topic
Show answer
Answer: C. joint inspectionThe statement describes joint inspection.
Report a mistake

Q41. Which statement best describes compound truss?

  1. Ais formed by connecting two or more simple trusses
  2. Bcontains no triangular units
  3. Cmust be unstable
  4. Dhas only two members
Show answer
Answer: A. is formed by connecting two or more simple trussesIn structural analysis, compound truss is correctly described as follows: is formed by connecting two or more simple trusses.
Report a mistake

Q42. Which concept is associated with the statement: “is formed by connecting two or more simple trusses”?

  1. Aa quantity unrelated to this topic
  2. Ba material-strength parameter only
  3. Ca drafting convention only
  4. Dcompound truss
Show answer
Answer: D. compound trussThe statement describes compound truss.
Report a mistake

Q43. Which statement best describes simple planar truss growth?

  1. Arequires adding three supports each time
  2. Brequires removing an existing joint
  3. Calways creates indeterminacy
  4. Dcan be formed by adding a new joint connected by two new members
Show answer
Answer: D. can be formed by adding a new joint connected by two new membersIn structural analysis, simple planar truss growth is correctly described as follows: can be formed by adding a new joint connected by two new members.
Report a mistake

Q44. Which concept is associated with the statement: “can be formed by adding a new joint connected by two new members”?

  1. Aa material-strength parameter only
  2. Ba drafting convention only
  3. Csimple planar truss growth
  4. Da quantity unrelated to this topic
Show answer
Answer: C. simple planar truss growthThe statement describes simple planar truss growth.
Report a mistake

Q45. Which statement best describes complex truss?

  1. Ais necessarily unstable
  2. Bcontains only cables
  3. Ccannot be classified as simple or compound by the usual simple construction rules
  4. Dhas no joints
Show answer
Answer: C. cannot be classified as simple or compound by the usual simple construction rulesIn structural analysis, complex truss is correctly described as follows: cannot be classified as simple or compound by the usual simple construction rules.
Report a mistake

Q46. Which concept is associated with the statement: “cannot be classified as simple or compound by the usual simple construction rules”?

  1. Aa drafting convention only
  2. Bcomplex truss
  3. Ca quantity unrelated to this topic
  4. Da material-strength parameter only
Show answer
Answer: B. complex trussThe statement describes complex truss.
Report a mistake

Q47. Which statement best describes compound-truss connection?

  1. Arequires every joint to be fixed
  2. Bmust provide adequate constraints between component trusses for stability
  3. Cmust always be a single roller
  4. Dcannot transfer forces
Show answer
Answer: B. must provide adequate constraints between component trusses for stabilityIn structural analysis, compound-truss connection is correctly described as follows: must provide adequate constraints between component trusses for stability.
Report a mistake

Q48. Which concept is associated with the statement: “must provide adequate constraints between component trusses for stability”?

  1. Acompound-truss connection
  2. Ba quantity unrelated to this topic
  3. Ca material-strength parameter only
  4. Da drafting convention only
Show answer
Answer: A. compound-truss connectionThe statement describes compound-truss connection.
Report a mistake

Q49. Which statement best describes analysis of complex trusses?

  1. Amay require systematic equilibrium or matrix methods beyond simple joint sequencing
  2. Bis impossible using mechanics
  3. Cnever uses equilibrium
  4. Drequires all members to have equal force
Show answer
Answer: A. may require systematic equilibrium or matrix methods beyond simple joint sequencingIn structural analysis, analysis of complex trusses is correctly described as follows: may require systematic equilibrium or matrix methods beyond simple joint sequencing.
Report a mistake

Q50. Which concept is associated with the statement: “may require systematic equilibrium or matrix methods beyond simple joint sequencing”?

  1. Aa material-strength parameter only
  2. Ba drafting convention only
  3. Canalysis of complex trusses
  4. Da quantity unrelated to this topic
Show answer
Answer: C. analysis of complex trussesThe statement describes analysis of complex trusses.
Report a mistake